#
# makefile:
#       makefile for src/dllstub directory.
#       For use with IBM NMAKE, which comes with the IBM compilers,
#       the Developer's Toolkit, and the DDK.
#
#       Called from:    main makefile
#
#       Input:          ./*.asm
#
#       Output:         ../bin/*.obj
#
#       Edit "setup.in" to set up the make process.
#

# Say hello to yourself.
!if [@echo +++++ Entering $(MAKEDIR)]
!endif

# include setup (compiler options etc.)
!include ..\..\config.in
!include ..\..\make\setup.in

# FIXED MACROS
# ------------
#
# You probably need not change the following.
#

# Define the suffixes for files which NMAKE will work on.
# .SUFFIXES is a reserved NMAKE keyword ("pseudotarget") for
# defining file extensions that NMAKE will recognize.
.SUFFIXES: .asm .obj

# OUTPUTDIR specifies the directory where all the output .OBJ
# files will be created in. $(XWP_OUTPUT_ROOT) is set by
# setup.in to point to \bin from the XWorkplace sources root,
OUTPUTDIR = $(XWP_OUTPUT_ROOT)
!if [@echo       OUTPUTDIR is $(OUTPUTDIR)]
!endif

# The OBJS macro contains all the .OBJ files which need to be created
# from the files in this directory. These will be put into BIN\.
OBJS = $(OUTPUTDIR)\xiniterm.obj

# The main target:
# If we're called from the main makefile, MAINMAKERUNNING is defined,
# and we'll set $(OBJS) as our targets (which will go on). Otherwise,
# we call the main makefile, which will again call ourselves later.
all:   \
!ifndef MAINMAKERUNNING
# we're not being called from main makefile: start main makefile
    callmainmake
    @echo ----- Leaving $(MAKEDIR)
!else
    $(OBJS)
    @echo ----- Leaving $(MAKEDIR)
!endif

callmainmake:
    @echo $(MAKEDIR)\makefile [$@]: Recursing to main makefile.
    @cd ..\..
    @$(MAKE)
    @echo $(MAKEDIR)\makefile [$@]: Returned from main makefile. Done.

# The "dep" target:
# there are no dependencies in this directory, so exit immediately
dep:
    @echo ----- Leaving $(MAKEDIR)

# xiniterm - rules to build xiniterm.obj:
# - to be committed to the repo so builders don't need to have ALP installed
# - to be copied to the output directory for use as the basis for xwpres.dll
# - to be copied to the NLS directories for use as the basis for xfldr0xx.dll

$(OBJS): $(MAKEDIR)\$(@B).obj
    $(COPY) $(MAKEDIR)\$(@B).obj $(OUTPUTDIR)

.asm.obj:
    @echo $(MAKEDIR)\makefile [$@]: Assembling $(@B).asm
    $(AS) $(MAKEDIR)\$(@B).asm

NLS_INITERM = \
$(PROJECT_BASE_DIR)\001\dll\xiniterm.obj \
$(PROJECT_BASE_DIR)\031\dll\xiniterm.obj \
$(PROJECT_BASE_DIR)\039\dll\xiniterm.obj \
$(PROJECT_BASE_DIR)\049\dll\xiniterm.obj \
$(PROJECT_BASE_DIR)\081\dll\xiniterm.obj

$(NLS_INITERM): $(MAKEDIR)\xiniterm.obj
    $(COPY) $? $@

# Special target "nls_xinit": this is not called by "all" but
# must the set on the NMAKE command line. It puts copies of
# xiniterm.obj in each of the NLS\dll directories. Since the
# .obj is already part of the repo, this should never be needed.
#
nls_xinit: $(NLS_INITERM)